Mortar Smash › Brick Calculator
Calculate bricks and mortar
Common projects: click to fill the calculator
Each preset sets the size, brick standard, wall thickness and a 10% waste allowance, then recalculates. Adjust any field afterwards.
Estimates only. Mortar figures assume solid bricks; frogged bricks laid frog-up and perforated bricks take noticeably more. Lime mortars and premixed bags have their own yields, so check the bag or your supplier before ordering. Concrete blocks: pick a block size and "Half brick, single leaf" for a single-leaf block wall; the count reads as blocks. Mortar for blocks assumes full bedding, so hollow US CMU laid with face-shell bedding uses less. For structural walls, follow your engineer or building regulations.
How many bricks for common jobs?
Short answer: a 5 m long, 1.2 m high freestanding garden wall one brick thick needs about 712 UK bricks, or 783 with 10% waste. A half-brick (single-leaf) wall uses about 60 UK bricks per m², so a 4 m × 2.4 m extension wall with 2 m² of windows and doors needs about 451 bricks, or 496 with waste. In the US, a modular single-leaf wall uses about 6.9 bricks per square foot — see bricks per square foot for the worked example.
These figures are this page's own calculator output, using a 10 mm joint (⅜ in for US modular), 10% waste and a 1 : 4 mortar mix. Press Load to put any row into the calculator and see the full working.
| Job | Wall size | Brick and thickness | Bricks, no waste | Bricks to order (+10%) | Wet mortar | Cement (approx.) | |
|---|---|---|---|---|---|---|---|
| Freestanding garden wall | 5 m × 1.2 m (6 m²) | UK 215 mm, one brick thick | 712 | 783 | 0.30 m³ | 5 × 25 kg, ~497 kg sand | |
| Low planter or raised-bed wall | 4 m × 0.45 m (1.8 m²) | UK, half brick | 107 | 118 | 0.035 m³ | 1 × 25 kg, ~58 kg sand | |
| Extension outer leaf (block inner leaf) | 4 m × 2.4 m less 2 m² (7.6 m²) | UK, half brick | 451 | 496 | 0.15 m³ | 3 × 25 kg, ~245 kg sand | |
| Garden seat or patio wall | 20 ft × 3 ft (60 sq ft) | US modular, two wythes | 823 | 905 | 9.3 cu ft | ~218 lb cement, ~970 lb sand | |
| Brick veneer house wall | 10 m × 2.4 m less 4 m² (20 m²) | Australian, single leaf | 969 | 1,066 | 0.37 m³ | 6 × 25 kg, ~617 kg sand | |
| Single-leaf wall, German bricks | 6 m × 2.5 m (15 m²) | German NF, single leaf | 741 | 815 | 0.30 m³ | 5 × 25 kg, ~501 kg sand |
Garden walls also need a coping or brick-on-edge course on top, and longer freestanding walls need piers or movement joints, all of which add bricks. Footings are not included. Check structural walls with a builder, engineer or your local building regulations.
How many bricks per square foot?
Short answer: about 6.9 US modular bricks per square foot for a single-leaf (veneer) wall with a ⅜ in joint, or about 13.7 per square foot for a solid wall two wythes thick. Add 5% to 10% for cuts and breakages.
US estimating tables often quote 6.75 modular bricks per sq ft. That figure comes from modular coursing (three courses rise exactly 8 inches), which implies a slightly thicker bed joint than a fixed ⅜ in. This calculator uses the brick size plus the joint you enter — for the default US modular ⅜ in joint that is about 6.85 per sq ft, rounded to 6.9 in the table below. Change the joint to match your spec if you need the modular-coursing number.
Worked example: a garden seat or patio wall 20 ft long × 3 ft high (60 sq ft), two wythes thick in US modular brick, needs about 823 bricks, or 905 with 10% waste, plus about 9.3 cu ft of wet mortar (~218 lb cement and ~970 lb sand at a 1:4 mix). Press Load on the "Garden seat or patio wall" row in the common-jobs table, or the US modular seat-wall preset above the form, to see the full working.
Figures are this page's own calculator output for US modular 7⅝ × 3⅝ × 2¼ in with a ⅜ in (9.5 mm) joint. Coping, piers and footings are not included.
How many bricks for a brick pier or pillar?
Short answer: a square 1½-brick pier (327.5 mm, the usual size for a garden-wall or gate pier) takes about 4½ standard UK bricks per course, which is roughly 60 bricks per metre of height. A 1-brick pier (215 mm) takes 2 bricks per course (about 27 per metre) and a solid 2-brick pier (440 mm) takes 8 per course (about 107 per metre). A pair of 1.8 m gate piers at 1½ bricks needs about 216 bricks, or 238 with 10% waste.
Wall area doesn't work for piers, so count by course instead: bricks per course × number of courses. UK bricks lay at 75 mm per course (65 mm brick plus a 10 mm joint); US modular brick lays three courses to 8 inches. A 12 × 12 in US modular pier works the same way as the UK 1½-brick pier (about 4½ bricks per course), and a 16 × 16 in pier takes 8. The half brick per course comes from cut bats in the bond, so some courses use 4 and some 5.
| Pier | Height and number | Courses | Bricks, no waste | Bricks to order (+10%) |
|---|---|---|---|---|
| UK 1-brick pier (215 mm) | 1 m, one pier | 14 | 28 | 31 |
| UK 1½-brick pier (327.5 mm) | 1 m, one pier | 14 | 63 | 70 |
| UK 1½-brick gate piers | 1.8 m, pair | 24 each | 216 | 238 |
| UK 2-brick pier (440 mm) | 1 m, one pier | 14 | 112 | 124 |
| US modular 12 × 12 in piers | 3 ft, pair | 14 each | 126 | 139 |
| US modular 16 × 16 in piers | 4 ft, pair | 18 each | 288 | 317 |
Courses are rounded up to whole courses, so a 1 m UK pier counts 14 courses (1.05 m). Solid piers only; hollow or reinforced piers, pier caps, coping and footings are not included. Gate piers carrying heavy gates usually need a steel or concrete core, so check with a builder or engineer.
How many bricks for a brick-on-edge coping?
Short answer: a brick-on-edge coping on a one-brick (215 mm) garden wall takes about 13⅓ standard UK bricks per metre of wall, because each brick stands on its side and fills 75 mm of length (65 mm brick plus a 10 mm joint). A 5 m garden wall needs 67 coping bricks, or 74 with 10% waste, on top of the bricks for the wall itself. In US modular brick, a rowlock cap across a two-wythe (7⅝ in) wall takes about 4.6 bricks per linear foot (2¼ in brick plus a ⅜ in joint), so a 20 ft seat wall needs 92, or 102 with 10% waste.
Coping is counted by length, not area: divide the wall length by the brick height plus one joint. A double brick-on-edge course doubles the figure, and walls finished with tile creasing under the coping need the creasing tiles counted separately. Brick-on-edge only works when the brick length matches the wall thickness, so a half-brick (102.5 mm) wall is usually finished with a coping stone or a brick-on-edge course laid along the wall instead.
| Coping | Wall | Bricks per metre or foot | Bricks, no waste | Bricks to order (+10%) |
|---|---|---|---|---|
| UK brick-on-edge | 5 m garden wall, 215 mm | 13⅓ per m | 67 | 74 |
| UK brick-on-edge | 10 m boundary wall, 215 mm | 13⅓ per m | 134 | 148 |
| UK double brick-on-edge | 5 m garden wall, 215 mm | 26⅔ per m | 134 | 148 |
| US modular rowlock cap | 20 ft seat wall, two wythes | 4.6 per ft | 92 | 102 |
Counts are rounded up to whole bricks. Coping takes the worst of the weather, so use frost-resistant bricks (F2 in the UK, SW grade in the US) and a strong mortar, and check with a builder for exposed sites. Piers usually get their own caps, which aren't included here.
How much concrete for a garden wall footing?
Short answer: a freestanding one-brick (215 mm) garden wall up to about 1 m high is usually built on a concrete strip footing about 450 mm wide and 225 mm deep, which is about 0.1 m³ of concrete per metre of wall. A 5 m garden wall needs about 0.51 m³, or 0.56 m³ with 10% waste: roughly eight 25 kg bags of cement, 390 kg of sand and 740 kg of gravel at a 1:2:4 mix (or about 1.1 tonnes of all-in ballast). A low half-brick wall needs about 300 × 150 mm, or 0.045 m³ per metre. In the US, a two-wythe seat wall on a 16 × 8 in footing takes about 0.9 cu ft per linear foot, so a 20 ft wall needs about 0.72 cu yd with 10% waste, or 33 bags of 80 lb premixed concrete.
A footing is counted by length × width × depth. A common rule of thumb is a footing two to three times as wide as the wall and at least as deep as the wall is thick, in a trench dug down to firm ground below frost depth (often 450 mm or more in the UK, and the local frost line in the US). Piers usually get a wider pad of their own. Dry materials shrink when mixed with water, so the figures above use a dry-to-wet factor of 1.54, with cement at about 1,440 kg/m³, sand 1,600 kg/m³ and gravel 1,500 kg/m³; one 80 lb bag of premix makes about 0.6 cu ft.
| Wall | Footing (width × depth) | Concrete, no waste | Concrete to order (+10%) | Cement at 1:2:4 |
|---|---|---|---|---|
| UK half-brick low wall, 5 m | 300 × 150 mm | 0.23 m³ | 0.25 m³ | 4 × 25 kg bags |
| UK one-brick garden wall, 5 m | 450 × 225 mm | 0.51 m³ | 0.56 m³ | 8 × 25 kg bags |
| UK one-brick boundary wall, 10 m | 450 × 225 mm | 1.01 m³ | 1.11 m³ | 15 × 25 kg bags |
| US two-wythe seat wall, 20 ft | 16 × 8 in | 17.8 cu ft | 19.6 cu ft (0.72 cu yd) | or 33 × 80 lb premix bags |
These are typical sizes for low freestanding garden walls on firm ground, not a design. Taller walls, retaining walls, clay or made-up ground, nearby trees and walls by a boundary or road need a builder or structural engineer, and local building rules apply. Once you know the footing, use the calculator for the bricks and the mortar calculator for the mortar.
How many concrete blocks per square metre?
Short answer: a standard UK concrete block (440 × 215 mm face, 10 mm joint) works out at about 9.9 blocks per m², so builders say 10 blocks per square metre. A 10 m² wall needs 99 blocks, or 109 with 10% waste. Laid flat in a 100 mm wall it takes about 0.0066 m³ of wet mortar per m², so the 10 m² wall needs about 0.07 m³ with waste: roughly 27 kg of cement (one and a bit 25 kg bags) and 120 kg of sand at 1:4. A 140 mm block needs about 40% more mortar. In the US a standard 8 × 8 × 16 in CMU (concrete masonry unit, 7⅝ × 7⅝ × 15⅝ in actual with a ⅜ in joint) covers 128 sq in, which is 1.125 blocks per square foot, so a 100 sq ft wall needs 113 blocks, or 124 with 10% waste.
The rule is the same as for bricks: 1 ÷ ((block length + joint) × (block height + joint)). Blocks are much bigger, so far fewer are needed, but each one is heavy (a dense 100 mm UK block weighs around 20 kg), and walls are often built in block and faced in brick. Openings are subtracted from the area before you count. To count your own wall, choose a block size in the calculator (UK 100 or 140 mm, or US 8 × 8 × 16 in CMU) with a single-leaf wall.
| Wall area | UK blocks (440 × 215 mm) | To order (+10%) | US wall area | US 8 × 8 × 16 in CMU | To order (+10%) |
|---|---|---|---|---|---|
| 5 m² | 50 | 55 | 60 sq ft | 68 | 75 |
| 10 m² | 99 | 109 | 100 sq ft | 113 | 124 |
| 20 m² | 198 | 218 | 200 sq ft | 225 | 248 |
Mortar figures assume full mortar beds and a 1:4 cement and sand mix, with the same dry-volume factor as the calculator above. Hollow US blocks are often laid on face-shell beds, which use less mortar, so check with your supplier. Load-bearing, retaining or reinforced block walls need a builder or engineer.
How much does a brick weigh?
Short answer: a standard UK clay brick (215 × 102.5 × 65 mm) weighs about 2.2 to 3.4 kg: roughly 2.2 to 2.7 kg for a perforated or frogged facing brick, about 2.9 kg for a solid one, and up to about 3.4 kg for a dense engineering brick. So 1,000 UK bricks weigh about 2.5 to 3 tonnes. A US modular brick (7⅝ × 3⅝ × 2¼ in) weighs about 3.5 lb cored and 4.5 lb solid, so 1,000 cored bricks are close to 2 short tons.
The weight is simply volume × density. A UK brick is 1.43 litres; fired clay is roughly 2,000 kg/m³, so a solid brick is about 2.9 kg, and holes or a frog take out 15% to 25%. A US modular brick is 1.02 litres, about 4.5 lb solid. A finished wall weighs more than the bricks alone because of the mortar: a half-brick UK wall comes to roughly 190 kg per m² (60 bricks plus about 0.018 m³ of mortar), a one-brick wall about twice that, and a single-wythe US brick wall about 40 lb per sq ft.
| Brick | One brick | Per 100 | Per 1,000 |
|---|---|---|---|
| UK perforated or frogged facing | 2.2 to 2.7 kg | 220 to 270 kg | 2.2 to 2.7 t |
| UK solid common | about 2.9 kg | about 290 kg | about 2.9 t |
| UK engineering (Class A/B) | 3.0 to 3.4 kg | 300 to 340 kg | 3.0 to 3.4 t |
| US modular, cored | about 3.5 lb | about 350 lb | about 1.75 short tons |
| US modular, solid | about 4.5 lb | about 450 lb | about 2.25 short tons |
Figures are estimates from standard brick sizes and typical fired-clay densities (about 2,000 kg/m³, engineering bricks up to about 2,350 kg/m³), with 22% voids assumed for perforated and cored bricks. Real weights vary by maker, clay and moisture, so check the manufacturer's data sheet, and check your van or trailer payload before collecting bricks yourself: a one-tonne payload is only about 350 to 450 UK bricks.
How the calculation works
Every brick takes up its own face plus one mortar joint on the side and one on top. So the number of bricks in one square metre of a single-leaf wall is:
bricks per m² = 1 ÷ ((brick length + joint) × (brick height + joint)), with sizes in metres.
For a UK brick with a 10 mm joint that is 1 ÷ (0.225 × 0.075) ≈ 59.3, which is why builders quote "about 60 bricks per square metre". A wall one brick thick, or a cavity wall with brick on both sides, uses two leaves, so roughly double. Openings for doors and windows are subtracted before multiplying, and a waste allowance (typically 5% to 10%) covers cuts, breakages and chipped faces.
Mortar is whatever fills the wall that isn't brick: the wall's volume minus the bricks' volume. To turn wet mortar into dry ingredients the calculator uses the common estimating rule that dry materials shrink by about 30% when mixed, a loose bulk density of about 1,440 kg/m³ for cement and 1,600 kg/m³ for damp building sand.
Last updated: 28 October 2026. Every figure on this page comes from the calculation described above; no results are guaranteed, and actual quantities depend on your bricks, joints, site and workmanship. This page is general information and an estimating aid, not professional, structural or engineering advice. Footing sizes, wall heights and mortar or concrete mixes depend on soil, exposure and local building rules, so confirm them with your local building control office or a qualified professional before you build.
Bricks per square metre by brick standard
Single-leaf (half-brick) wall with a 10 mm (or ⅜ in) joint, no waste:
| Brick standard | Size | Bricks per m² | Bricks per sq ft | One brick thick, per m² |
|---|---|---|---|---|
| UK metric | 215 × 102.5 × 65 mm | 59.3 | 5.5 | 118.5 |
| US modular | 7⅝ × 3⅝ × 2¼ in | 73.8 | 6.9 | 147.6 |
| German NF | 240 × 115 × 71 mm | 49.4 | 4.6 | 98.8 |
| Australian | 230 × 110 × 76 mm | 48.4 | 4.5 | 96.9 |
US tables often say 6.75 modular bricks per square foot because modular coursing assumes three courses rise exactly 8 inches, a slightly thicker bed joint than ⅜ in. German tables quoting 48 NF bricks per m² assume a 12 mm bed joint. Change the joint size in the calculator to match your spec.
Common questions
How many bricks are in a 1 m² wall?
About 60 standard UK bricks for a single-leaf wall, or about 120 for a solid wall one brick thick. Add 5% to 10% for waste.
How many bricks do I need for a garden wall?
Multiply length by height to get the face area, choose "one brick thick" if it is a freestanding 215 mm wall (most garden walls over about 450 mm high are built that way for stability), and add waste. Don't forget the coping or brick-on-edge course on top, which uses extra bricks (about 13⅓ per metre; see coping).
How many bricks do I need for a 5 metre garden wall?
A freestanding garden wall 5 m long and 1.2 m high, one brick thick (215 mm) in standard UK bricks, needs about 712 bricks, or 783 with 10% waste. It also needs about 0.3 m³ of wet mortar, roughly five 25 kg bags of cement and 500 kg of sand at a 1:4 mix. Add extra bricks for the coping course and any piers.
How many bricks do I need for a brick pillar?
A square 1½-brick pier (327.5 mm) in standard UK bricks takes about 4½ bricks per course, or roughly 60 bricks per metre of height, so a 1.8 m gate pier needs about 108 bricks and a pair about 216 (238 with 10% waste). A 1-brick pier takes about 27 bricks per metre and a solid 2-brick pier about 107. In US modular brick a 12 × 12 in pier also takes about 4½ bricks per course and a 16 × 16 in pier 8. See bricks for piers and pillars.
How many bricks do I need for a brick-on-edge coping?
About 13⅓ standard UK bricks per metre of wall for a brick-on-edge coping on a one-brick (215 mm) wall, so a 5 m garden wall needs 67, or 74 with 10% waste. A double brick-on-edge course needs twice as many. In US modular brick a rowlock cap on a two-wythe wall takes about 4.6 bricks per linear foot, so a 20 ft wall needs 92, or 102 with 10% waste. See bricks for coping.
How much concrete do I need for a garden wall footing?
About 0.1 m³ per metre of wall for a one-brick (215 mm) garden wall on a typical 450 mm wide, 225 mm deep strip footing, so a 5 m wall needs about 0.51 m³, or 0.56 m³ with 10% waste: roughly eight 25 kg bags of cement, 390 kg of sand and 740 kg of gravel at a 1:2:4 mix. A low half-brick wall needs about 0.045 m³ per metre. In the US, a 20 ft two-wythe seat wall on a 16 × 8 in footing needs about 0.72 cu yd with waste, or 33 bags of 80 lb premixed concrete. See garden wall footings. Taller or retaining walls need a builder or engineer.
How many concrete blocks per square metre?
About 10 standard UK concrete blocks (440 × 215 mm face with a 10 mm joint) per square metre, exactly 9.9, so a 10 m² wall needs 99 blocks or 109 with 10% waste. In the US an 8 × 8 × 16 in CMU covers 1.125 blocks per square foot, so a 100 sq ft wall needs 113 blocks or 124 with 10% waste. See concrete blocks.
How much does a brick weigh?
A standard UK clay brick (215 × 102.5 × 65 mm) weighs about 2.2 to 3.4 kg: around 2.2 to 2.7 kg perforated or frogged, about 2.9 kg solid and up to 3.4 kg for an engineering brick, so 1,000 bricks weigh about 2.5 to 3 tonnes. A US modular brick weighs about 3.5 lb cored or 4.5 lb solid. A half-brick wall weighs roughly 190 kg per m² including mortar. See brick weight.
Does the bond pattern change the number of bricks?
Not for the same wall thickness. Stretcher, English and Flemish bonds all fill the same area; they just arrange the headers and stretchers differently. What changes the count is the thickness. See our guide to brick bonds.
How much mortar do I need per 1,000 bricks?
For UK bricks in a single-leaf wall, roughly 0.3 m³ of wet mortar per 1,000 solid bricks before waste, and more for frogged bricks. The calculator works it out from your exact size and joint, and the mortar calculator works it out from a brick count, with cement and sand per 1,000 bricks.
How many bricks per square foot for a modular brick wall?
About 6.9 US modular bricks (7⅝ × 3⅝ × 2¼ in) per square foot of single-leaf wall with a ⅜ in mortar joint, or about 13.7 for a solid wall two wythes thick. Estimating tables often quote 6.75 per sq ft because modular coursing assumes three courses rise exactly 8 inches, which uses a slightly thicker bed joint than ⅜ in. Add 5% to 10% for waste.
How many bricks for a 20 ft by 3 ft seat wall?
A freestanding garden seat or patio wall 20 ft long and 3 ft high, two wythes thick in US modular brick, needs about 823 bricks, or 905 with 10% waste. It also needs about 9.3 cu ft of wet mortar, roughly 218 lb of cement and 970 lb of sand at a 1:4 mix. Add extra bricks for a coping course and any piers.
Done with the maths?
Knock a wall down instead of building one.
Play Mortar Smash →